Dr. Flash needs some advice again ;)

i tried the instructions for the Ambika firmware flashing in the manual, control board worked (tested)
with the voicecard atmega avrdude gave me error messages in fuse bits and eeprom parts.
i can’t try if that particular chip works now, as it’s one of my spares and i wanted to try first, since mine are all on board already and i need to flash some for another user too.
here’s avrdude’s saying:

C:\\>avrdude -B 100 -V -p m328p -c usbtiny -P usb -e -u -U efuse:w:0xfd:m -U hfus
e:w:0xde:m -U lfuse:w:0xff:m -U lock:w:0x2f:m

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.04s

avrdude: Device signature = 0x1e950f
avrdude: current erase-rewrite cycle count is -256 (if being tracked)
avrdude: erasing chip
avrdude: reading input file "0xfd"
avrdude: writing efuse (1 bytes):

Writing | | 0% 0.00s *****faile
d;
Writing | ################################################## | 100% 0.09s

avrdude: 1 bytes of efuse written
avrdude: reading input file "0xde"
avrdude: writing hfuse (1 bytes):

Writing | ################################################## | 100% 0.01s

avrdude: 1 bytes of hfuse written
avrdude: reading input file "0xff"
avrdude: writing lfuse (1 bytes):

Writing | ################################################## | 100% 0.01s

avrdude: 1 bytes of lfuse written
avrdude: reading input file "0x2f"
avrdude: writing lock (1 bytes):

Writing | ################################################## | 100% 0.05s

avrdude: 1 bytes of lock written

avrdude done. Thank you.

C:\\>avrdude -B 1 -V -p m328p -c usbtiny -P usb -U flash:w:ambika_voicecard.hex:i
-U flash:w:ambika_voicecard_boot.hex:i -U eeprom:w:ambika_voicecard_eeprom_gold
en.hex:i -U lock:w:0x2f:m

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.01s

avrdude: Device signature = 0x1e950f
avrdude: NOTE: FLASH memory has been specified, an erase cycle will be performed

To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file "ambika_voicecard.hex"
avrdude: writing flash (28546 bytes):

Writing | ################################################## | 100% 18.50s

avrdude: 28546 bytes of flash written
avrdude: reading input file "ambika_voicecard_boot.hex"
avrdude: writing flash (32762 bytes):

Writing | ################################################## | 100% 17.69s

avrdude: 32762 bytes of flash written
avrdude: reading input file "ambika_voicecard_eeprom_golden.hex"
avrdude: writing eeprom (1024 bytes):

Writing | | 0% 0.00s
avrdude: error: usbtiny_send: usb_control_msg: sending control message failed, w
in error: Der E/A-Vorgang wurde wegen eines Threadendes oder einer Anwendungsanf
orderung abgebrochen.
(expected 128, got -116)
Writing | ################################################## | 100% 2.51s

avrdude: 1024 bytes of eeprom written
avrdude: reading input file "0x2f"
avrdude: writing lock (1 bytes):

Writing | ################################################## | 100% 0.01s

avrdude: 1 bytes of lock written

avrdude: safemode: Fuses OK

avrdude done. Thank you.

C:\\>

sorry for the german, my avrdude is just unilingual

i got a similar note from avrdude when i did the internal eeprom for the Shruthi 4PM yesterday.
however Shruthi shows the patches 1-16 now. to verify if they work i have to wait for tonight.

so, i’m not sure if this is ok as is, but i suspect it should run without any failed and errors, right?